The use method and daily maintenance of meat grinder


The use method and daily maintenance of meat grinder Ho […]

The use method and daily maintenance of meat grinder
How to use the meat grinder:
1. Flush
Every time you use the meat grinder, you have to rinse it briefly. Generally speaking, the meat grinder is cleaned in time after the last time it is used up. The cleaning before use is mainly to wash away the floating dust inside and outside the machine. Another advantage is that the rinsing before use will make the minced meat easier and smoother, and it will also make the cleaning after work easier.
2. Installation
Many people like to install the machine completely after each mincing, but in fact this method is not advisable. Ideally, after each use, the cleaned meat grinder should be placed in a wooden cabinet in the form of loose parts, or it should be completely dried before being assembled. It is not suitable to be assembled immediately.
The installation starts with the assembly. The roller is fed into the machine cavity. In order to reduce wear, a drop of edible oil can be placed on the shaft, and then the knife head is installed on the roller, paying attention to the knife edge facing outward. Then install the leak to the cutter head, shake gently to make the three closely fit the machine cavity, and then install the solid nut to the outside of the leak, pay attention to the tightness, too loose will cause the meat to leak from the side seam, too tight will cause Damage to the wire mouth. Finally, install the twist handle, pay attention to the handle facing outwards, align the notch and put it in, and then screw on the firm screw.
It is relatively simple to install the machine. The most important thing is to choose suitable fixing parts, such as a relatively large wooden chopping board, align the bite with the chopping board, and tighten the fastening screws behind the edge. Because the meat is relatively hard, it is best to use a screwdriver and other tools to help the machine to be firm when fixing the machine to prevent the machine from loosening during work.
3. Operation
The real ground meat is relatively simple, because it is more forceful, so it is best to have a male operation, or two people can cooperate. If it is mincing dumplings, it is best to mince a green onion before mincing the meat, which will save a lot of effort. Wash the meat, cut into long strips, and slowly feed in (the more meat you feed, the more effort it takes). After the meat is minced, you can also mince another green onion, or vegetables such as potatoes. To put it bluntly, this is a kind of cleansing in disguise, and it can also reduce the waste of minced meat.
4. Cleaning
First prepare a clean toothbrush, test tube brush and other auxiliary supplies, and then unload the machine in the opposite direction to clean out the fleshy meat in the machine cavity, and then soak the machine in warm water containing detergent, use a toothbrush, etc. Clean all the parts one by one, and then rinse twice with tap water. Put it in a cool and ventilated place to control dry.
Daily maintenance of meat grinder:
Refueling problem
1. Under normal use of the meat grinder, there is no need to refuel within one year;
2. The lubricating oil of the meat grinder is butter;
3. Oil filling hole position: One bolt hole at the back of the two bolt holes on the top of the fuselage (the direction away from the minced meat parts) can facilitate oil filling (be sure to add butter, not liquid oil).
Daily maintenance
The chassis of the meat grinder does not need to be maintained under normal conditions, mainly for waterproofing and protecting the power cord, avoiding damage to the power cord, and cleaning it.
Routine maintenance of meat grinder parts: after each use, the meat grinder tee, screw, blade orifice plate, etc. need to be disassembled, and the residues are removed and then reinstalled in the original order. The purpose of this is to ensure the sanitation of the machine and processed food on the one hand, and on the other hand to ensure that the meat grinder parts are flexible in disassembly and assembly, which is convenient for maintenance and replacement. The blades and orifice plates are vulnerable parts and may need to be replaced after a period of use.

Views: 48